Atten GT-5150P Single Channel Desoldering station with GT-X150P Desoldering Gun

• Built-in vacuum suction pump.

• The maximum output is 150 W.

• Can automatically recognise the connected soldering tools and upload the corresponding parameters.

• Software for control via a PC

• compatible with various types of soldering tools

• Intuitive menu navigation

• Display of parameter data and information in the form of a graphic on a large display

• 3 adjustable temperatures available at the touch of a button

• Very fast heat-up: from room temperature to 350 Celsius Degree in only approx. 7 s

• High-contrast multifunction LC display for status and programming display

• Readiness for operation checked by bar display

• flexible connection cable with plug-in system

• Temperature freely selectable between 150 Celsius degree. and 480 Celsius Degree.

• Precise temperature calibration possible, calibration range + - 50 Celsius degree.

• Temperature stability: +- 2 Celsius degree. (without load / MCU-controlled temperature calibration)

• Temperature setting possible in 5-degree or 1-degree increments

• Automatic, adjustable temperature reduction during soldering breaks to 150 Celsius degree. (1-120 min)

• Protection against temperature adjustment

• ESD-safe design, low-voltage heating completely separated from the power supply

• Freely positionable holder

• Intelligent detection of working or non-working status.

• 1x GT-510 negative pressure generator

• 1x S-21 desoldering iron holder

• 1x GT-X150P desoldering gun

• 1x T151-0.8 nozzle

• 1x T151-1.0 nozzle

• 1x T151-1.3 nozzle

• 1x T151-1.6 nozzle

• 2x power cord

• 1x connection line

• 1x grounding wire

• 3x solder suction

• 2x cleaning pin

• 1x twist drill

• 2x O-ring seal

• 10x filter (cotton)

• 10x filter (paper)

• 1x inner pipe (carbon spring)

• 2x pipe front holder

• 1x open-end wrench

• 1x cleaning pin set

• Power output: 150 watts

• Temperature range: 150 Celsius Degree - 480 Celsius Degree

• Temperature offset range: +-50Celsius Degree

• Temperature setting: 5 digits (standard) / 1 digit (fine-tuning)

• Temperature stability: 2 Celsius Degree

• Heating element: with silver alloy

• ESD protection: Yes

• Earthing resistance: < 2 Ohm

• Earth potential: < 2 mV

• Weight: 5.68 kg

• Channel: 1

• Power supply: 230 V / 50 Hz

• RoHS: Compliant

SHIPPING

A delivery and handling charge applies to all orders with the exception of back-ordered items.

Unless otherwise required by Buyer, Seller will make transport arrangements as follows:

For deliveries within the metropolitan areas of mainland State capital cities a standard freight charge may be added to invoice; goods

For delivery outside those areas, seller will select the transport to be used and prepay freight for Buyer. Seller will then bill Buyer for freight at Seller's discretion.

Should the Buyer request goods be sent to a Post Office box the Buyer acknowledges this method is the only available and therefore the Seller is not liable for undelivered goods.

Free shipping on orders over $199 incl GST (valid for 1 delivery per order and excludes NT, WA & TAS). If only part of the order is in stock, the customer has the option of paying for a second delivery if they require a partial shipment prior to all goods becoming available. Mektronics Australia reserves the right to charge additional freight in the event of hazardous, bulky or heavy items ordered.

DELIVERY TIME

All quoted delivery or consignment dates are estimates only, given without engagement.

Delay in consignment of any part of an order shall not relieve Buyer of its obligation to accept and pay for the remainder of the order.

Except as provided in paragraph 1.2 of Terms & Conditions, seller will not be liable to pay damages or compensation for any injury or loss sustained by Buyer

a) in the event of a delay in consignment or delivery of goods: or

b) in the event of non delivery.

Goods offered ex-stock by Seller are subject to prior sale.

In the event of any happening beyond Seller's reasonable control in consequence of which Seller cannot effect consignment by the time or times quoted or specified, Seller shall be entitled to consign part only of an order, suspend consignment or extend the time for consignment, for the period during which such cause of delay operates, or may cancel the order, and in the event of such suspension, extension or cancellation, Seller shall not be liable for damages.